Need to know how to adjust Cobra Darkspeed Fairway Woods to switch the loft and lie angles? We have a complete guide and adjustment chart.

The Cobra Darkspeed woods are fully adjustable with a hosel offering you the opportunity to adjust the loft to increase or decrease your launch angle

The amount of adjustment you can make differs from brand to brand but the step-by-step guide below shows you how the Cobra Darkspeed fairways woods can be adjusted.

Cobra Darkspeed Fairway Woods Lofts

The Cobra Darkspeed Fairway Woods are sold in three different models – the X, Max and LS.

The Darkspeed X woods are available in 3-wood (15 degrees), 3 HF-wood (16.5 degrees), 5-wood (18 degrees) and 7-wood (21 degrees).

The Darkspeed Max woods are available in 3-wood (15.5 degrees), 5-wood (18.5 degrees) and 7-wood (21.5 degrees).

The Darkspeed LS woods are available in 3-plus wood (13 degrees), 3-wood (14.5 degrees) and 5-wood (17.5 degrees).

Cobra Darkspeed X Woods Specs

Loft: 3-wood (15 degrees), 3 HF-wood (16.5 degrees), 5-wood (18 degrees) and 7-wood (21 degrees)

Standard Length: 43 inches, 42.5 inches & 42 inches

Standard Lie: 58.2 degrees, 57.5 degrees & 56.7 degrees

Adjustability: 3 degrees of adjustability with the following options (-1.5° / -1° / -1° Draw / STD° / STD° Draw / +1° / +1° Draw / +1.5°)

Cobra Darkspeed Max Woods Specs

Loft: 3-wood (15.5 degrees), 5-wood (18.5 degrees) and 7-wood (21.5 degrees)

Standard Length: 43 inches, 42.5 inches & 42 inches

Standard Lie: 59.2 degrees, 58.5 degrees & 57.7 degrees

Adjustability: 3 degrees of adjustability with the following options (-1.5° / -1° / -1° Draw / STD° / STD° Draw / +1° / +1° Draw / +1.5°)

Cobra Darkspeed LS Woods Specs

Loft: 3-plus wood (13 degrees), 3-wood (14.5 degrees) and 5-wood (17.5 degrees)

Standard Length: 43 inches & 42.25 inches

Standard Lie: 56.2 degrees & 55.7 degrees

Adjustability: 3 degrees of adjustability with the following options (-1.5° / -1° / -1° Draw / STD° / STD° Draw / +1° / +1° Draw / +1.5°)

Adjusting The Loft Angle of Cobra Darkspeed Fairway Woods

There are a few simple steps you can take to adjust the loft angle of your fairway. You will just need an adjustment tool or wrench to get started.

Here’s how to adjust Cobra Darkspeed Fairway Woods:

1. Locate the screw on the sole of your Cobra Darkspeed Woods that attaches the fairway head to the shaft.

2. Using the wrench, loosen the screw by turning anticlockwise.

3. Once the screw is fully out, you can rotate the adjustable hosel to a lower loft or a higher loft depending on your preference. You will notice the loft figure you had the driver set to and be able to turn the shaft to up to 16 further options.

4. When you have turned the hosel to your required loft, slot the shaft back into your club head. Your new loft will be display through the window on most clubs.

5. Put the screw back in place and tighten with the wrench by turning clockwise. When it is fully tight, you will hear a crank that sounds like the clubhead is cracking. At this point, the screw is as tight as needed.

Every time you want to adjust the loft, you repeat this process.